Visit The Dirt Forum for More Information

Author Topic:   9" BRACKETS
bigcityracer
Member
posted March 23, 2004 07:31 AM
Who sells the weld on brackets to install a 9" in a metric car??


WesternAuto17
Member
posted March 23, 2004 07:34 AM
WWW.SPEEDWAYMOTORS.COM
WWW.MOSERENGINEERING.COM
WWW.QUICKPERFORMANCE.COM

Need any others?

bigcityracer
Member
posted March 23, 2004 07:58 AM
quote:
Originally posted by WesternAuto17:
WWW.SPEEDWAYMOTORS.COM
WWW.MOSERENGINEERING.COM
WWW.QUICKPERFORMANCE.COM

Need any others?


I looked on all three site but don't see any metric brackets to weld on the 9"



UFnARacing
Member
posted March 23, 2004 09:23 AM
You might have to call speedway motors. I just saw the kit that includes all the brackets for (ouch) $179! It may not be on the internet sight, but it is in the catalog.


WesternAuto17
Member
posted March 23, 2004 10:31 AM
The Speedway part number is 91048336. You can type it in under the part number search.


6pack
Member
posted March 23, 2004 08:11 PM
cut the ones off the stock metric then make your own on the top save yourself a bunch of money or better yet take it to a chassis shop and have them jig it so it's done right you'd be amazed how much better the car works with the rear set with the right angels from the get go


superdave
Member
posted March 23, 2004 09:52 PM
[QUOTE]Originally posted by 6pack:
[B] http://www.aa-mfg.com

$6.27 each for the bottom and $4.81 each for the top. Tough price to beat.

Good luck,
Superdave


bigcityracer
Member
posted March 23, 2004 10:24 PM
THANKS DAVE AND 6PACK.
THAT'S WHAT I'M TALKIN ABOUT. CHEAP!!


boas51
Member
posted March 25, 2004 07:31 AM
I got mine from quickperformance.com, I ordered it with the stock metric mounts already jig welded, and moser axels installed for 500


19J
Member
posted March 28, 2004 11:23 PM
It all mounts like the stock 10 bolt rear end.


bigcityracer
Member
posted March 29, 2004 10:01 PM
Droper23 / Do you have a part # to look up. THANKS FOR THE REPLY


droper23
Member
posted March 30, 2004 09:15 PM
Sorry the price was 675, I must have had something else on my mind. If you go to the quick performance link at the beginning of this post, go down and click on rear ends in about the middle of the page. Then go down to the heavy duty 9" bolt in housings. The housing is only 285, with the Moser axles, bearings, retainers and studs, the price is 675. I called them and told them how wide I wanted it and they made it to my specs and had the axles done to fit my rear end. It is a very nice rear end. Hope this helps, again sorry about the price mix up earlier.


19J
Member
posted March 30, 2004 11:20 PM
dropper, how much did they hit you for shipping, ive been looking at these rearends.Also how many miles was it shipped. Thanks.
19j, thats not a real bad price for what you get. My moser axles were $300 alone, another 375 to have a housing cut to your preference and jigged doesen't seem bad to me.



WesternAuto17
Member
posted March 31, 2004 07:45 AM
I got mine from Moser. It was $888 with shipping.

[This message has been edited by WesternAuto17 (edited March 31, 2004).]

droper23
Member
posted March 31, 2004 11:31 PM
I will have to look into how much the shipping was, will get back with you.


Back to the Archives