Visit The Dirt Forum for More Information

Author Topic:   rearend straightening?
jlfastride
Member
posted October 24, 2002 08:19 AM
i just found during winter teardown that my rear end housing is bent not visibly but it is toe'ed out about 3/4 inch any ideas on correcting this problem short of buying a new 375 dollar housing i know you can heat the long side and gain some with shrinkage. let me know , thanks in advance. jl


Racer14K
Member
posted October 24, 2002 02:21 PM
I have seen an adapter thats slides over the bearing snout on the tube and then use a potra-power to straighten the tube. I thought Coleman Racing Products made it but I can't find it in their catalog, i'll keep looking though.


outlawstock17
Member
posted October 24, 2002 02:48 PM
i think afco makes a rear end straightener for use with a port-a-power.


istock59
Member
posted October 24, 2002 03:03 PM
If it's a floater housing, the chassis shops around here can remove the bent tube and replace it. I've had mine done a couple times. $100 per, if I remember right.


Racer14K
Member
posted October 24, 2002 03:10 PM
Yep, that's where it was, just seen it on their on-line catalog. Said for wide 5 tubes though, $84.00.


hamer36
Member
posted October 26, 2002 09:30 AM
Since you're in the mod section I'll assume you're talking about a 9". Those afco units are for the wide 5.
What I do is remove gear set, and put wheels and tires on the rearend. I put it on my grain scales so that I can fully rotate the rear without pullbar mount hitting the floor. I put a dial indicator on the scale upright to measure and find exactly there the tube is bent...you do this by rotating the rear and seeing the wheel wobble and dial indicator read the changes. To move the tube forward, heat the bend red hot with a rosebud torch. About 2" circle is good. Now quence it with cold water via a garden hose. It must be cooled as fast as possible to move it the most. Repeat along tube as necessary. Once you have "treated" an area of a tube, it won't move if repeated again, so move to area down the tube.rotate rear to see if fixed.You get wet but this method works.


2nd2none
Member
posted October 26, 2002 10:19 AM
i've got a home made straightner thats works well, used it twice this year. If anyone wants plans or if jammin would like to have it in the tools section let me know.


jammin
Administrator
posted October 26, 2002 03:05 PM
Send the plans to me, I will put them up for everyone. I would love to see them in the toolbox.

jammin

[This message has been edited by jammin (edited October 26, 2002).]

2nd2none
Member
posted October 26, 2002 04:09 PM
check you're email jammin


dkandy94
Member
posted October 26, 2002 04:25 PM
I run a shop where we have a jig to straighten all types of housings. I recommend that you don't heat the housing at all!!!! It will make the housing weak & take the spring out of the tubes. we straighten rear housings for $150.00. if interested lmk.any straightening must be done COLD!!! Good luck.


jammin
Administrator
posted October 26, 2002 08:28 PM
Thanks 2nd! Awesome.

jammin

autoshop
Member
posted October 28, 2002 10:06 AM
Will get it up asap!

jammin


jlfastride
Member
posted October 30, 2002 09:15 PM
thanks for the relpy's guys im starting to think that the r snout is what is bent not sure yet though haven't been able to check 70 hours a week at work and trying to hit the swap meets, lol. anything else as far as do i straighten the snout or replace it.?


jammin
Administrator
posted October 31, 2002 08:15 AM
The plans are in the toolbox!

jammin


2nd2none
Member
posted October 31, 2002 05:48 PM
The plans are about as good as i could do, if anyone needs more info/help let me know.