Visit The Dirt Forum for More Information

Author Topic:   Chassis X bracing
dode
Dirt Freak

Total posts: 417
posted October 11, 2002 03:46 PM UIN: 13209501
What is the best material for doing this in a Metric car, and how is the best way to deal with getting around the driveshaft? I need to get started on this, but having a brain lapse. Can someone help? Thanks.

John

loojack
Dirt Maniac

Total posts: 133
posted October 11, 2002 04:22 PM
dode, I used roll bar tubing on mine, I'm sure 1 1/2" will work fine. As far as getting around the driveshaft, have the "X" cross as near the rear of the trans as possible. It's easier with the body and interior removed.(bare frame) Also I put the "X" under the trans level. This stumped me too. I ended up looking at pic's of how other people did it. Hope this helps! loojack

dode
Dirt Freak

Total posts: 417
posted October 11, 2002 04:24 PM UIN: 13209501
Hmmm...that kinda made sense, but kinda not. Do you have these pics that you talked about? I have looked around but couldn't find any. Right now I have a bare frame to work with, so the sky is the limit basically.

John

racer17j
Dirt Forum Champ
Total posts: 1565
posted October 11, 2002 04:27 PM UIN: 54865418
we just use 1 1/4 tubing that we use in the chassis just makes a simple x and mount it as low in the frame rails as posible we have even mounterd them on the bottom with some angle iron to make tabs to weld it too then take some 1x3 square and make your cross member

dode
Dirt Freak

Total posts: 417
posted October 11, 2002 04:29 PM UIN: 13209501
how big should I make it? like spacing between the two tubes on one side of the car, and how far forward or back should it be? The rear one I have figured out...

John

outlawstock17
Dirt Forum Champ
Total posts: 620
posted October 11, 2002 04:35 PM
dode, i agree with loojack on placement of the "X". cross the tubes directly behind transmission. it also makes a handy place to mount your driveshaft loop. i use 1"x2" square tube for the "X" brace.

outlawstock17
Dirt Forum Champ
Total posts: 620
posted October 11, 2002 04:38 PM
it will be strongest if you make the "X" square. the tubes should intersect at a 90 degree angle.

dode
Dirt Freak

Total posts: 417
posted October 11, 2002 04:39 PM UIN: 13209501
quote:
Originally posted by outlawstock17:
it will be strongest if you make the "X" square.

Please explain this.

John

[This message has been edited by dode (edited October 11, 2002).]

outlawstock17
Dirt Forum Champ
Total posts: 620
posted October 11, 2002 04:50 PM
make the "X" as wide as it is long. however wide your frame rails are is how long your "X" should be to have the most strength.

hope this helps, it's kind of hard to explain with a keyboard.

two additional 1"x2" tubes perpendicular to the frame rails running from the center of the "X" out to the frame rail on both sides will make your car super stout.

[This message has been edited by outlawstock17 (edited October 11, 2002).]

dode
Dirt Freak

Total posts: 417
posted October 11, 2002 04:51 PM UIN: 13209501
Oh...I thought you were talking about square tubing...LOL...dang I need some sleep. That 4 am trip to the airport has me all messed up.

John

Eljojo
Dirt Freak

Total posts: 273
posted October 11, 2002 07:45 PM
I "x'd my metric and made the intersection of the two 1"X2" tubing behind the trans just as loojack suggested. I also ran one across the car like outlawstock said-it saved my car from being destroyed one night. The frame "puckered" on both sides, but if it weren't there I'll betcha that shot in the door would have bent an un braced frame at least 5"or 6"! I also used a piece ot 1/4" flat stock on top of the X to support the rear of the trans.

BK19
Dirt Freak

Total posts: 285
posted October 11, 2002 08:41 PM UIN: 40696038
go to www.laynesworld and click on the terminator link there are pics of stock car x'd

BK19
Dirt Freak

Total posts: 285
posted October 11, 2002 10:20 PM UIN: 40696038

Eljojo
Dirt Freak

Total posts: 273
posted October 11, 2002 10:26 PM
.........any questions? LMAO!!!!!!

widebody
Dirt Maniac

Total posts: 197
posted October 15, 2002 01:20 PM
Heres mine, somethings simular to BK19.
http://www.yager.net/motorsports/prostock/2001/10-24-01.jpg

Howd you get the picture in there??

loojack
Dirt Maniac

Total posts: 133
posted October 15, 2002 03:33 PM
Great website Widebody! That 10 car is one sweet ride! Thanks for the look! loojack

BK19
Dirt Freak

Total posts: 285
posted October 15, 2002 07:52 PM UIN: 40696038
widebody you highlite the pic right click then click on properties and copy the url the follow these instructions
Adding Images
To add a graphic within your message, just encase the URL of the graphic image as shown in the following example
[IMG] [/IMG] <<< you put the url in btween those img symbols
In the example above, the UBB Code automatically makes the graphic visible in your message. Note: the "http://" part of the URL is REQUIRED for the [img] code. Also note: some UBB forums may disable the [img] tag support to prevent objectionable images from being viewed.
go to this faq link it will explain it all

http://www.thedirtforum.com/ubb/faq.html


[This message has been edited by BK19 (edited October 15, 2002).]

[This message has been edited by BK19 (edited October 15, 2002).]

[This message has been edited by BK19 (edited October 15, 2002).]

o5racer
Dirt Maniac

Total posts: 115
posted October 15, 2002 10:05 PM


o5racer
Dirt Maniac

Total posts: 115
posted October 15, 2002 10:10 PM
OMG it actually worked!!!
Its not the best pic but you can kinda see what i did. I used 1 1/4 .125 tubing.

widebody
Dirt Maniac

Total posts: 197
posted October 16, 2002 01:42 PM
Wow i learn something new everytime i come here, and it wasnt even a race car topic. Ya gotta love it!!
Here goes the all new 2002 Prostock

This is the same car from the last post, just a new skin and an updated front end for 2002..

ryan
Dirt Freak

Total posts: 430
posted October 16, 2002 04:11 PM
I thought I would give it a try. I have tried to put my picture on the user pictures but it would not work for me.

[This message has been edited by ryan (edited October 16, 2002).]

o5racer
Dirt Maniac

Total posts: 115
posted October 17, 2002 01:59 AM
[img]http://us.f1.yahoofs.com/users/e79c0e35/bc/Yahoo!+Photo+Album/2002.jpg?bcaof19A79LQ04Ep[img/]

ryan
Dirt Freak

Total posts: 430
posted October 17, 2002 04:20 PM
Here is nicks car. We race at the same track and I didn't even know other people from Riviera were on here.

[This message has been edited by ryan (edited October 17, 2002).]

skawldeddawg
Dirt Full Roller

Total posts: 30
posted November 05, 2002 05:32 PM
[IMG]C:\My Documents\My Pictures\dawgpage8\raceready.jpg[/IMG] heres my before look
skawlded dawg

skawldeddawg
Dirt Full Roller

Total posts: 30
posted November 05, 2002 05:36 PM
trying again [IMG]C:\My Documents\My Pictures\dawgpage8\raceready.jpg[IMG/]<<<

BK19
Dirt Freak

Total posts: 285
posted November 05, 2002 06:47 PM UIN: 40696038
skawldeddawg the image has to be on a website http addy to get the pic to show up on here you cant use pictures from your personal pics on your computer

Back to the Archives