Visit The Dirt Forum for More Information

Author Topic:   parts and misc for sale
BK19
Dirt Freak

Total posts: 285
posted August 28, 2002 05:36 PM UIN: 40696038
well i thought i would be getting back into racing but right now it dont look good so i am going to sell all my parts i have 1 buick regal there is a fender missing i have some a arms and 1 frame that the rear horns are rotted out cloud be use to stubb a car
400sbc block 2-bolt with caps 150.00
350 sbc 2 bolt with crank 100.00
327 large journal 100.00
a few 305's
valve covers 1 tall set with breathers
alot of misc heads,cranks and intakes
2 rogchester carbs 1 is ready to go 1 needs rebuild i have kits for both
metric rearends
75 cutlauss rearend housing's bolt in axles
87 bronco for parts
89 dodge pickup burnt wiring harness
84 s-10 jimmy for parts
82 w wheel drive suburban for parts
snap on wire feed welder
60 gallon 5 horse single stage upright air comporessor
mac tool cam bearing tool
proform sbc distributer 50,000 volt coil
1975 camaro in pretty good shap no motor
i have a stand made out of i-beam good for pulling motors or lifting bodies off
i just have alot of things to sell email keechracing19@aol.com cell phone 612=382-5205

Radrcr869
Dirt Full Roller

Total posts: 30
posted August 28, 2002 09:56 PM
How much for the Rochester Carbs?? What are the off ??

BK19
Dirt Freak

Total posts: 285
posted August 28, 2002 09:58 PM UIN: 40696038
the one that i was using 75.00 with a new kit
the other one 50.00 with the kit i dont know what they were off of but i will get the numbers tomorrow and post them they are both the "bigger "ones

Radrcr869
Dirt Full Roller

Total posts: 30
posted August 30, 2002 10:01 AM
OK I would like to see the numbers off them

BK19
Dirt Freak

Total posts: 285
posted August 30, 2002 06:14 PM UIN: 40696038
ok the carb that i was using the number is 7041118
the other carb # is 7029115

BK19
Dirt Freak

Total posts: 285
posted September 01, 2002 01:11 AM UIN: 40696038
the 400 block is sold
the rogchester carbs are sold
the dodge truck is sold
the distributer is sold

buckseight
Dirt Maniac

Total posts: 106
posted September 02, 2002 06:28 AM
whats rhat wire feed ? 110 or 220 volts. asking?

BK19
Dirt Freak

Total posts: 285
posted September 02, 2002 08:51 AM UIN: 40696038
its actually 115 this welder weld 1/4 inch in a single pass it has 100 % duty cycle i welded my cage in my old car with it a rolled it 3 different nights and the cage did not break or crack anywhere

Rookieracer76
Dirt Maniac

Total posts: 182
posted September 02, 2002 09:56 PM
How much for the welder,cranks,intake,rearends? Thanks! Also What does the crank and and intake fit ?

BK19
Dirt Freak

Total posts: 285
posted September 03, 2002 08:17 AM UIN: 40696038
welder with the tall cart 500.00 cranks need turning 25.00 fit 350 sbc intakes i have 2 and 4 barrel sbc price depnds which one you want 15.00- 40.00 metric rearend 40.00 the older cutlass 10 bolt housings25.00

NYhick
Dirt Forum Racer

Total posts: 82
posted September 05, 2002 06:49 AM
what is the price on the compressor, what brand, condition, and your location.

highfill
Dirt Roller

Total posts: 6
posted October 06, 2002 08:58 PM
interrested in welder where are you located and does it have bottle with it can email me at racindirtfever@yahoo thanks

2nd2none
Dirt Freak

Total posts: 368
posted October 07, 2002 02:00 PM
how much for the mac cam bearing tool???

BK19
Dirt Freak

Total posts: 285
posted October 07, 2002 04:35 PM UIN: 40696038
the welder and cam tool are sold sorry actually pretty much everything is sold thanks

Back to the Archives